在印刷過程中，版型是否翹曲決定了生產效率。如果版材翹曲，不僅會影響生產效率，還會造成很大的生產損失。那么如何解決印刷翹曲問題呢？

In the printing process, whether the plate is warped determines the production efficiency. If the plate warps, it will not only affect the production efficiency, but also cause great production loss. So how to solve the problem of printing warpage?

滾筒上的鎖版裝置松動會導致印版翹曲。鎖版裝置松動，印版安裝印刷時，印版受力松緊，長時間使用印版開始發熱。一旦受熱過大，粘度就會降低，到一定程度會導致印版脫落，印版翹曲。因此，必須定期檢查鎖緊裝置，不能松動。一旦松動，就會影響印刷質量，還會出現重影、脫墨、網點堵塞等現象。

Looseness of the plate locking device on the cylinder will lead to warpage of the printing plate. The plate locking device is loose. When the printing plate is installed and printed, the printing plate is tensioned, and the printing plate starts to heat after long-time use. Once heated too much, the viscosity will be reduced, which will lead to the falling off of the printing plate and the warping of the printing plate to a certain extent. Therefore, the locking device must be checked regularly without loosening. Once loose, it will affect the printing quality, and there will be ghosting, deinking, dot blocking and other phenomena.

印版會翹起，多半是因為雙面膠不粘。雙面膠分為白色和黃色兩種。黃色膠帶易撕，貼錯容易改變位置，但粘性較差。因此，在制作柔版印刷版時，白色膠帶優于黃色膠帶。用白膠帶貼印版時，一定要量好距離再采用一定的生產標準，貼版好，不翹邊。

The printing plate will tilt up, mostly because the double-sided tape is not sticky. The double-sided adhesive tape is divided into white and yellow. The yellow tape is easy to tear and paste incorrectly, which is easy to change the position, but the viscosity is poor. Therefore, when making flexographic printing plate, white tape is better than yellow tape. When pasting the printing plate with white tape, be sure to measure the distance, and then adopt a certain production standard to paste the plate well without edge warping.

印刷后存放不當也會導致印版翹曲。許多打印機存儲卷曲的印版，這會在印版和底座的邊緣產生張力。在生產過程中或拆卸印版時，會出現黃樟的現象。水在印版的邊緣。水只要卷曲儲存起來，很容易滲入印版，導致膠帶不粘，造成翹曲。因此，第一次印刷完成后，應將印版鎖緊密封，以免發生翹曲現象。

Improper storage after printing will also lead to plate warpage. Many printers store curled plates, which creates tension at the edges of the plate and base. In the production process or when disassembling the printing plate, there will be the phenomenon of yellow camphor. Water is on the edge of the printing plate. As long as water is curled and stored, it is easy to penetrate into the printing plate, resulting in non stick tape and warpage. Therefore, after the first printing, the printing plate should be locked and sealed to avoid warpage.

山東印刷包裝廠家總結下：材料使用不當、人員操作不當、設備原因等，都會造成印刷翹曲。我們需要做的是控制影響印刷翹曲的因素，提高生產效率。更多相關內容就來網站www.096685.com咨詢吧！

Shandong printing and packaging manufacturers concluded that improper use of materials, improper operation of personnel, equipment reasons, etc. will cause printing warpage. What we need to do is to control the factors affecting printing warpage and improve production efficiency. For more relevant content, please come to the website for consultation!