濟南印刷表明，很多時候在印刷過程中出現各種各樣的問題，比較常見的問題便是印刷紙張出現脫毛掉粉，那么面對這樣的狀況要如何處理呢？

　　Ji 'nan printing shows that many times there are a variety of problems in the printing process, the most common problem is the removal of the printing paper powder, so in the face of this situation how to deal with it?

　　一般紙制品質量不好，會導致紙毛、除粉失敗。經營者除了建議造紙廠家盡快提高產品質量要求退貨外，還可以根據印刷紙張的具體情況采取相應的措施。

　　General paper product quality is not good, will lead to paper wool, powder removal failure. In addition to advising paper-making manufacturers to improve product quality as soon as possible, managers can also take corresponding measures according to the specific conditions of printed paper.

　　由于油墨的粘度太容易造成紙張掉毛掉粉，所以應適當調整所用油墨的粘度，可在油墨中加入適量的增粘劑和稀釋劑來降低粘度以提高油墨的粘度，打結在紙上的效果。

　　Because the viscosity of ink is too easy to cause paper wool off powder, so it should be appropriate to adjust the viscosity of the ink, can be added in the ink viscosity and diluent to reduce the viscosity to improve the viscosity of the ink, knot on paper effect.

　　對于容易掉毛、掉粉的紙張，如膠版紙、凸版紙、書寫紙等，打印傳單前務必將紙張晾干，并清除紙屑、紙粉、紙屑和紙張表面的灰塵。

　　For the paper that is easy to lose hair and powder, such as offset paper, letterpress paper, writing paper, etc., be sure to dry the paper before printing leaflets, and remove the dust on the paper surface, paper powder, paper scraps and paper.

　　濟南印刷建議應該調整印刷壓力，適當降低橡皮滾筒與壓印滾筒之間的壓印力，或選擇合適的印刷速度，適當降低速度。這降低了壓花后橡皮布和紙張之間的剝離張力。

　　Ji 'nan printing suggestions should adjust the printing pressure, appropriately reduce the impression force between the rubber drum and the embossing drum, or choose the appropriate printing speed, appropriately reduce the speed. This reduces the stripping tension between blanket and paper after embossing.

　　紙張由于原料及制造工藝等原因，在印刷過程中可能會脫粉、掉毛的現象，堆積在橡皮布的表面上，從而影響網點正確傳遞，嚴重時每印1千張左右就得擦洗橡皮布，否則橡皮布上粘滿了脫粉掉毛，印刷出來的產品光澤度明顯下降。因此，有條件的情況下在紙張表面上套印一道白墨和清水，多擦洗橡皮布。

　　Paper due to raw material and manufacturing process, in the printing process may take off powder, wool phenomenon, accumulation on the surface of rubber cloth, thus affecting site right transfer, serious when every printed thousand or so have to scrub rubber blanket, blanket or on the stick full powder dropping off, printed products gloss decreased obviously. Therefore, conditional conditions on the surface of the paper overprint a white ink and water, scrub blanket.

　　綜上所述，印刷紙脫粉、掉毛的原因，不僅是紙張表面強度低造成的，還包括填料和施膠材料選擇不當，壓光不足等。更多相關內容的了解就請來這里www.096685.com咨詢吧。

　　To sum up, the reason for printing paper powder, hair, is not only caused by the low surface strength of paper, but also includes improper selection of filler and sizing materials, insufficient pressing and so on. For more information, please visit www.096685.com.